KIKUSUI PWX Series Programmable DC Power Supply
Sepete ekleyerek toplu teklif isteyebilirsiniz
KIKUSUI PWX Series Programmable DC Power Supply
KIKUSUI PWX Series Programmable DC Power Supply A Next-Generation Rack-Mounted Power Supply A wide range of voltage and current settings can be combined within its output power rating (3times) A thin and lightweight design with a 1U height for increased rack-mounting efficiency Rated output power : 750W / 1500W, Rated output power : 30V / 80V / 230V / 650V PFC circuit of 0.99 (with 100V) or 0.97 (with 200V) at full load *TYP value Features Equipped with standard LAN interface and VMCB function to support network-based remote control and monitoring The PWX series is equipped with LAN, USB, and ...
Açıklama
KIKUSUI PWX Series Programmable DC Power Supply
- A Next-Generation Rack-Mounted Power Supply
- A wide range of voltage and current settings can be combined within its output power rating (3times)
- A thin and lightweight design with a 1U height for increased rack-mounting efficiency
- Rated output power : 750W / 1500W, Rated output power : 30V / 80V / 230V / 650V
- PFC circuit of 0.99 (with 100V) or 0.97 (with 200V) at full load *TYP value
Features
Equipped with standard LAN interface and VMCB function to support network-based remote control and monitoring
The PWX series is equipped with LAN, USB, and RS232C interfaces as standard features. By using the feature of virtual multi-channel bus (VMCB)*1span>, it allows you to control remotely and monitoring for 1-to-N as well as N-to-M for large-scale networks. In particular, the LAN interface is LXI compliant, enabling you to easily control and monitor the power supply through a browser on a PC, smart-phone, or tablet by accessing the web server built into the PWX series. Additionally, the optional application software, Wavy for PWX (SD013-PWX), sequence creation and control sof tware, allows you to change settings for specific channels (in individual) on VMCB-connected PWX series power supplies, and lets you perform batch control using global commands*2. You can also turn the output ON and OFF on multiple units and adjust the output voltage and current.*1: This function for the PWX750ML applies to the firmware version 2.0 and later. *2: This is only enabled for “Direct control” on Wavy for PWX. Global commands that can be also used under control with VXI-11, HiSLIP, and SCPI-RAW.
Basic configuration with LAN interface and VMCB (example)
As shown in the figure below, it is possible to connect a PC and the PWX series with a hub to create a virtual group using a LAN connec-tion. A maximum of 255 virtual groups can be set, and the maximum number of units can be configured up to 31 units per group. A group can have a mixture of models. Configuration IP address Domain number Channel number Master 192.168.1.1 1 0 Slave 192.168.1.2 1 1 192.168.1.3 1 2A DHCP server can also establish settings automatically
Additional feature is adopted!
Communication Monitoring function: This function monitors the communication status. For example, the alarm will be activated and the output will be turned off when the LAN cable is disconnected and the communication is not being confirmed within the specified time of setting. This function protects the operation from the uncontrolled condition, and it improves the system reliability. *Applies to the firmware Ver.2.2X or aboveSecurity for LAN connections Access to the built-in web server can be restricted with a password. Also, when using VXI-11, HiSLIP, and SCPI-RAW for control, host restrictions can be set with the IP address. It is possible to prevent access from any terminal other than the ones registered as a host (up to 4 hosts can be registered).
LAN Interface
The LAN inter face can control the number of devices with high speed, and it’s theoretical controllable maximum number is to be calculated by approximately 4.2 billion. (The maximum transmission speed varies by the number of connected devices) In accordance with its applied standard, it is possible to combine the device that is to control or to be controlled, it is also the feature that can be used with various applications. Also, in computers installed with Apple Bonjour, it is possible to access with a host name instead of the IP address.The PWX series can automatically identify the type of LAN cable whether straight or cross is connected and it connects using the appropriate method.
